Call Tech Support 1-800-423-9696

Tech Support: 1-800-423-9696
Wednesday 11/22/2017
Closed Now

 
Ford 3G Alternator Harness By Painless Performance

P/N 30831

Ford 3G Alternator Harness

       
 

  • Application
  • Specs
  • Larger Image
American Made

 

The popular Ford 3G Alternator conversion just got easier. The Painless 3G kit takes the parts chase away from this ever growing charging system upgrade. Until now, pigtails, large gauge charge wire, and a heavy duty inline fuse have all had to be sourced individually. This kit comes with both alternator connectors pre-installed, 8’ of large 6 gauge charge wire, a weather-proof fuse holder with a heavy duty 150 amp inline fuse, detailed instructions, and all weatherproof splices & ring terminals needed for a proper install.

 

    This kit contains all of the components needed in order to connect a Ford 3G Alternator. This kit will contain the following:

(1) 7’ Red 6 gauge charge wire

(1) 8’ Black/Red ground wire

(2) Pre-installed connectors (a 3 pin connector and 1 pin connector)

(1) Bag kit containing (150 amp in-line fuse, 1 fuse holder, 2 screws, 6 large un-insulated ring terminals, 4 smaller insulated ring terminals, 4 splices, 4 pieces of heat shrink & 15 zip ties)

 Ford 3G Alternator Harness By Painless Performance

 

 

ECM Flash Program

 

 

This is a basic start and run tune that we only recommend for a near stock application. We will only change the following parameters: delete VATS/PASS-KEY security, cooling fan on/off temperatures, rear end gear ratio, tire size, speed limiter, rpm limiter, idle rpm, and we will adjust the check engine light parameters. If your setup requires any other parameters tuned you will need to locate a local tuner. All ECMs are left unlocked to allow easy access for your tuner.

Step 1: Purchase one of the qualifying part numbers. See below for that list.


Step 2: If your part number is highlighted RED proceed to step 3B. If your part number is highlighted BLACK, proceed to step 3A.


Step 3A: If you have arrived at this step, your harness does not come with an ECM and you must provide one to be flashed. Please reference the manual with your harness to confirm the ECM part number required.


Step 4A: Once you have received your harness, please cut the Barcode label from the box as shown in the picture below.


Step 5A: Package and mail your ECM along with the Barcode label, a copy of your purchase receipt, and your ECM form that you are about to complete. (The address will be provided after you complete the form). We will pay for return ground shipping*. If you request a faster service, you will need to provide a return label.


Step 3B: If you have arrived at this step, your purchase comes with an ECM. You must fill out our ECM form BEFORE your purchase will ship. Proceed to Step 6.


Step 6: Click the “Start Here” button below to fill out our ECM questionnaire.


Step 7: Once we have the ECM, we will use the data from the form to flash the ECM. Then, once it has been flashed we will package the ECM and ship it back to you. If we encounter a question, we will contact you. This process can take 1-3 days.


Step 8: Once you receive your ECM, it is ready to go.

 

*Note: Our free return shipping is ONLY good for the lower 48 states, via ground UPS. If you are outside of those states, you must provide a return shipping label with your order. If your purchase comes with an ECM, the shipping will be covered via the retailer you purchased from.

 

 

Click the Start Here button below to get your FREE ECM Flash!

Click Here To Start The ECM Reflash Process

 

End Panel


APPLICABLE PAINLESS PART NUMBERS

60008

   

60522

60009

   

60523

60017

   

60524

60026

   

60526

60217

   

60608

60218

   

60617

60221

   

60700

60508

   

60701

60509

   

60702

60520

   

60710