Call Tech Support 1-800-423-9696

Tech Support: 1-800-423-9696
Wednesday 11/22/2017
Closed Now

 
Ford 1986 - 1995 5.0L Fuel Injection Wiring Harness Extra Length By Painless Performance

P/N 60511

Ford 1986 - 1995 5.0L Fuel Injection Wiring Harness Extra Length

       
 

  • Application
  • Specs
  • Larger Image
Year: 1986 - 1995
Make: Ford
Model: Passenger Car
Engine: 5.0 H.O. Mass Air flow
Trans.: None
American Made

 

This harness is designed for the 1986-1995 Ford 5.0 (car) HO EFI engines. You must use the 1989-1993 MAF, Distributor, and ECM. 1986-1988 must add MAF (mass air flow) sensor. 1994-1995 must modify TPS wiring and change distributor. Harnesses do not include all the original connections for the original emissions but are available separate. Included with this harness is an 8 circuit modular fuse block and Ford color coded wires with labels for easy installation. 

This extended length harness allows eight feet from the back of the intake manifold to where the fuseblock and ECM mount. Perfect for those that plan to mount these components under the seat or in the center console.

 

This kit includes:

  1. All new fuel injection harness with OEM fitment connectors and harness breakouts
  2. Diagnostic connector and check engine light
  3. Rubber grommet
  4. Mounting hardware

We HIGHLY recommend checking the online manual for the full list of required mating parts prior to ordering.  

 

Number of Circuits: 8 Fuses with 2 Ignition & 1 Fuel Pump Relay
Harness Length: 8 Feet Between Engine and ECM
Fuse Type: Blade
Firewall Passthrough: Grommet
Color Code Based: 1990 Mustang
Circuit Designations: Printed Wire Tags on all Connectors and Open Ended Wires

The Fuse Block Protects The Following Circuits:

  • Check Engine Light
  • Driver Side Injectors
  • Dual 40 amp Ignition Relays
  • EEC-IV
  • Fuel Pump Relay (B+)
  • Fuel Pump Relay (IGN)
  • Heated O2 Sensors
  • Mass Airflow, EVR, ISC
  • Pass Side Injectors

 

 

 

This harness includes connections for the following components:

  • Alternator
  • Barometric Pressure Sensor
  • Data Link Connector 
  • ECM
  • EEC Ground
  • EEC Power Relay
  • EEC Test
  • EGR Vacuum Regulator
  • EGR Valve
  • Engine Coolant Temperature
  • Fuel Pump
  • Fuel Pump Relay
  • Grounds 
  • Idle Air Control
  • Ignition Coil
  • Ignition Switch Signal 
  • Ignition Timing Setting
  • Injectors
  • Intake Air Temperature
  • Malfunction Indicator Lamp
  • Mass Airflow Sensor
  • Neutral Safety Switch
  • O2 Sensor
  • Starter Relay
  • Tachometer
  • TFI Ground
  • TFI Pigtail
  • Throttle Position Sensor
  • VSS

 


Other 5.0HO harnesses offered by Painless Performance®™:

60510- Standard length version of 60511


 Ford 1986 - 1995 5.0L Fuel Injection Wiring Harness Extra Length By Painless Performance

 

 

ECM Flash Program

 

 

This is a basic start and run tune that we only recommend for a near stock application. We will only change the following parameters: delete VATS/PASS-KEY security, cooling fan on/off temperatures, rear end gear ratio, tire size, speed limiter, rpm limiter, idle rpm, and we will adjust the check engine light parameters. If your setup requires any other parameters tuned you will need to locate a local tuner. All ECMs are left unlocked to allow easy access for your tuner.

Step 1: Purchase one of the qualifying part numbers. See below for that list.


Step 2: If your part number is highlighted RED proceed to step 3B. If your part number is highlighted BLACK, proceed to step 3A.


Step 3A: If you have arrived at this step, your harness does not come with an ECM and you must provide one to be flashed. Please reference the manual with your harness to confirm the ECM part number required.


Step 4A: Once you have received your harness, please cut the Barcode label from the box as shown in the picture below.


Step 5A: Package and mail your ECM along with the Barcode label, a copy of your purchase receipt, and your ECM form that you are about to complete. (The address will be provided after you complete the form). We will pay for return ground shipping*. If you request a faster service, you will need to provide a return label.


Step 3B: If you have arrived at this step, your purchase comes with an ECM. You must fill out our ECM form BEFORE your purchase will ship. Proceed to Step 6.


Step 6: Click the “Start Here” button below to fill out our ECM questionnaire.


Step 7: Once we have the ECM, we will use the data from the form to flash the ECM. Then, once it has been flashed we will package the ECM and ship it back to you. If we encounter a question, we will contact you. This process can take 1-3 days.


Step 8: Once you receive your ECM, it is ready to go.

 

*Note: Our free return shipping is ONLY good for the lower 48 states, via ground UPS. If you are outside of those states, you must provide a return shipping label with your order. If your purchase comes with an ECM, the shipping will be covered via the retailer you purchased from.

 

 

Click the Start Here button below to get your FREE ECM Flash!

Click Here To Start The ECM Reflash Process

 

End Panel


APPLICABLE PAINLESS PART NUMBERS

60008

   

60522

60009

   

60523

60017

   

60524

60026

   

60526

60217

   

60608

60218

   

60617

60221

   

60700

60508

   

60701

60509

   

60702

60520

   

60710