Call Tech Support 1-800-423-9696

Tech Support: 1-800-423-9696
Tuesday 11/21/2017
Open today at 8AM

 
GM 1997 - 2004 LS1 LS6 W/ 4L60E Mech. TB Integrated Fuel Injection & Chassis By Painless Performance

P/N 60608

GM 1997 - 2004 LS1 LS6 W/ 4L60E Mech. TB Integrated Fuel Injection & Chassis

GM Column IgnitionIn Dash Ignition
       
 

  • Application
  • Specs
  • Larger Image
  • ECM Re-Flash
Year: 1997 - 2004
Make: General Motors
Model: Camaro, Firebird, Corvette
Engine: 5.7L LS1 / LS6 w/ Cable Throttle Body
Trans.: 4L60E
Free ECM Flash American Made

 

Our integrated EFI/Chassis harnesses are the perfect solution for anyone doing a complete rewire of a vehicle as well as transplanting a GM Gen III fuel injected engine. This kit is designed for use on 1997-2004 LS1 engines with a 4L60E transmission. The chassis wiring and fuel injection wiring are fully integrated into a single 26 circuit/7 relay fuse block, eliminating the need to have separate fuses and relays for the fuel injection. The chassis harness connections are the same GM color coded connections as our 10201 kit. The fuel injection connections include the same labels connections as our 60508 harnesses. These harnesses do not support flex fuel engines and require the use of a mechanical throttle body. Included in this kit you will also find all the required terminals & connectors for easy installation.   

 

This harness also requires the following mating parts; ECM #12200411 (Painless # 60700) 

Purchase this harness today and qualify for Painless Performance®™ to flash your ECM for free.  Click here for details.

We recommend checking the online manual for the full list of required mating parts prior to ordering.  

 

Number of Circuits: 26 Fuse with 7 Relays
Fuse Type: Mini Blade & Maxi Fuse
Firewall Passthrough: Multiple Grommet
Color Code Based: 2000 Camaro
Circuit Designations: Printed Wire Tags on all Connectors and Printed on Wire for Open Ended Wires

This harness has the following chassis connections:

  1. A/C & Heat
  2. Accessory / Cigarette Lighter
  3. Backup Lights
  4. Brake Lights
  5. Charging
  6. Cruise Control
  7. Courtest & Dome Light
  8. Electric Fuel Pump
  9. Emergency Flashers
  10. Cooling Fan Relay #1
  11. Cooling Fan Relay #2
  12. Fused Power Source
  13. Headlights
  14. Horn Relay
  15. Ignition Coil
  16. Instrument Panel Lighting and Gauges
  17. Park Lights
  18. Power Antenna
  19. Power Door Locks
  20. Power Windows
  21. Radio/Clock (Constant and Switched) 
  22. Starting
  23. Tail Lights
  24. Third Brake Light
  25. Turn Signals
  26. Wipers

 

The fuel injection harness includes connections for the following components:

  • A/C Compressor
  • Alternator 
  • Cam Position Sensor
  • Coolant Temperature Gauge
  • Crank Position Sensor
  • Data Link Connector 
  • Driver/Pass Front O2 Sensors
  • Engine Coolant Temperature
  • Fuel Pump Relay
  • Grounds 
  • Idle Air Control
  • Ignition Coils
  • Ignition Switch Signal
  • Injectors
  • Intake Air Temperature Sensor
  • Knock Sensors
  • Malfunction Indicator Lamp
  • MAP Sensor
  • Mass Airflow Sensor
  • Oil Pressure Gauge
  • ECM
  • PRNDL Switch
  • Starter
  • Tachometer
  • Throttle Position Sensor
  • Transmission
  • Vehicle Speed Sensor
  • VSS Output for Speedometer

 GM 1997 - 2004 LS1 LS6 W/ 4L60E Mech. TB Integrated Fuel Injection & Chassis By Painless Performance

 

 

ECM Flash Program

 

 

This is a basic start and run tune that we only recommend for a near stock application. We will only change the following parameters: delete VATS/PASS-KEY security, cooling fan on/off temperatures, rear end gear ratio, tire size, speed limiter, rpm limiter, idle rpm, and we will adjust the check engine light parameters. If your setup requires any other parameters tuned you will need to locate a local tuner. All ECMs are left unlocked to allow easy access for your tuner.

Step 1: Purchase one of the qualifying part numbers. See below for that list.


Step 2: If your part number is highlighted RED proceed to step 3B. If your part number is highlighted BLACK, proceed to step 3A.


Step 3A: If you have arrived at this step, your harness does not come with an ECM and you must provide one to be flashed. Please reference the manual with your harness to confirm the ECM part number required.


Step 4A: Once you have received your harness, please cut the Barcode label from the box as shown in the picture below.


Step 5A: Package and mail your ECM along with the Barcode label, a copy of your purchase receipt, and your ECM form that you are about to complete. (The address will be provided after you complete the form). We will pay for return ground shipping*. If you request a faster service, you will need to provide a return label.


Step 3B: If you have arrived at this step, your purchase comes with an ECM. You must fill out our ECM form BEFORE your purchase will ship. Proceed to Step 6.


Step 6: Click the “Start Here” button below to fill out our ECM questionnaire.


Step 7: Once we have the ECM, we will use the data from the form to flash the ECM. Then, once it has been flashed we will package the ECM and ship it back to you. If we encounter a question, we will contact you. This process can take 1-3 days.


Step 8: Once you receive your ECM, it is ready to go.

 

*Note: Our free return shipping is ONLY good for the lower 48 states, via ground UPS. If you are outside of those states, you must provide a return shipping label with your order. If your purchase comes with an ECM, the shipping will be covered via the retailer you purchased from.

 

 

Click the Start Here button below to get your FREE ECM Flash!

Click Here To Start The ECM Reflash Process

 

End Panel


APPLICABLE PAINLESS PART NUMBERS

60008

   

60522

60009

   

60523

60017

   

60524

60026

   

60526

60217

   

60608

60218

   

60617

60221

   

60700

60508

   

60701

60509

   

60702

60520

   

60710