Call Tech Support 1-800-423-9696

Tech Support: 1-800-423-9696
Friday 01/19/2018
Open today at 8AM

 
8 Point Distribution Blocks-Red & Black By Painless Performance

P/N 80116

8 Point Distribution Blocks-Red & Black

       
 

  • Application
  • Specs
  • Larger Image
American Made

 

Use these blocks anywhere power or ground distribution is necessary. No more overloading battery terminals with numerous feeds to different components.

 

We’ve had many calls from those building fiberglass bodied kit cars/off road vehicles for a product making it easier to find common grounding points. We’ve also heard from those installing products like our relay banks and Extreme Off Road Harness looking for a common place to source power from in order to power the circuit breakers in these kits without having to run everything to the battery. These distribution blocks handle both of these needs perfectly. One main stud (3/8" on the red, 5/16" on the black) makes it easy to supply power or ground directly to the block. There are 8 screws positioned around the stud making it easy to re-direct the main source to components on your chassis harness. Self tapping mounting screws are provided with each kit.

An individual red block is available as part #80114 and an individual black block is available as part #80115

 8 Point Distribution Blocks-Red & Black By Painless Performance

 

 

ECM Flash Program

 

 

This is a basic start and run tune that we only recommend for a near stock application. We will only change the following parameters: delete VATS/PASS-KEY security, cooling fan on/off temperatures, rear end gear ratio, tire size, speed limiter, rpm limiter, idle rpm, and we will adjust the check engine light parameters. If your setup requires any other parameters tuned you will need to locate a local tuner. All ECMs are left unlocked to allow easy access for your tuner.

Step 1: Purchase one of the qualifying part numbers. See below for that list.


Step 2: If your part number is highlighted RED proceed to step 3B. If your part number is highlighted BLACK, proceed to step 3A.


Step 3A: If you have arrived at this step, your harness does not come with an ECM and you must provide one to be flashed. Please reference the manual with your harness to confirm the ECM part number required.


Step 4A: Once you have received your harness, please cut the Barcode label from the box as shown in the picture below.


Step 5A: Package and mail your ECM along with the Barcode label, a copy of your purchase receipt, and your ECM form that you are about to complete. (The address will be provided after you complete the form). We will pay for return ground shipping*. If you request a faster service, you will need to provide a return label.


Step 3B: If you have arrived at this step, your purchase comes with an ECM. You must fill out our ECM form BEFORE your purchase will ship. Proceed to Step 6.


Step 6: Click the “Start Here” button below to fill out our ECM questionnaire.


Step 7: Once we have the ECM, we will use the data from the form to flash the ECM. Then, once it has been flashed we will package the ECM and ship it back to you. If we encounter a question, we will contact you. This process can take 1-3 days.


Step 8: Once you receive your ECM, it is ready to go.

 

*Note: Our free return shipping is ONLY good for the lower 48 states, via ground UPS. If you are outside of those states, you must provide a return shipping label with your order. If your purchase comes with an ECM, the shipping will be covered via the retailer you purchased from.

 

 

Click the Start Here button below to get your FREE ECM Flash!

Click Here To Start The ECM Reflash Process

 

End Panel


APPLICABLE PAINLESS PART NUMBERS

60008

   

60522

60009

   

60523

60017

   

60524

60026

   

60526

60217

   

60608

60218

   

60617

60221

   

60700

60508

   

60701

60509

   

60702

60520

   

60710