Call Tech Support 1-800-423-9696

Tech Support: 1-800-423-9696
Wednesday 11/22/2017
Closed Now

 
Trail Rocker System Jeep Wrangler TJ 1997-06 w/Dash Mounted Panel By Painless Performance

P/N 57040

Trail Rocker System Jeep Wrangler TJ 1997-06 w/Dash Mounted Panel

       
 

  • Application
  • Specs
  • Larger Image
Year: 1997-2006
Make: Jeep
Model: TJ
American Made

 

Introducing the brand new Trail Rocker from Painless, allowing you to control up to eight accessories on your TJ Jeep! The heart of this kit is enclosed in the weatherproof housing that surrounds the power center with eight fuses and relays. Controlling it, are eight prewired switches mounted in our custom switch panel that mounts on your dash.The power center then provides you with all the necessary weatherproof connectors and wiring to connect to your Jeep accessories ranging from lights to air lockers. Easily installed with our detailed instructions and plug-n-play design.

 •Control up to eight accessories, (8) 30 amp fuses and (8) 30 amp relays
 •Weatherproof housing around the power center and connections
 •Custom bolt-on powder coated bracket for the power center
 •Switch panel mounts eight LED switches in a factory non-intrusive dash location

Winch Ready! The Trail Rocker system includes dedicated wires for controlling a winch. Purchase of our Winch Control Add-on Kit part number 57150 is required for operation. 

 

The top of the weatherproof fuse & relay center features the stylish logo silkscreened onto it. Along with the fused power source mounted next to it. Underneath the fuse & relay center you will find the powder coated custom mounting bracket with stainless hardware. This bracket is designed to install in existing mounting holes under the hood. 

 

The heart of the Trail Rocker is the fuse & relay center. Here you will find eight 30 amp fuses and eight 30 amp relays. 

 

The 200 Amp MIDI fuse comes pre-installed ready to protect your investment! 

The underside of the fuse & relay cover has a built in gasket to help keep any moisture out and to act as an extra support for the relays. This extra support on the relays ensures that no matter how good or bad you are on the trails, the relays will not pop out of place. 

Attention to detail shows in this bolt with O-ring combo to hold the top cover on.  

 

 

These switches are vibration, shock, thermoshock, moisture, and salt spray resistant. This panel mounts on top of your dash over your existing cubby hole. Don't worry though, we provide you a new cubby to place your goods in along with a padded insert. 

The back side of the switch panel comes pre terminated and ready to plug into the fuse & relay center. 

This harness attaches the fuse & relay center to the switch panel. It’s a plug-n-play design that only requires you to route it and plug it in.  

Exiting the fuse & relay center we provide you with 21’ of wire to reach any 12 volt accessory you have.

Printed every 12” on the wire you’ll find the circuit description, a signature touch of ours. 

The parts kit comes with everything you’ll need to install the Trail Rocker, except the tools and the Jeep.

You’ll also find a custom pigtail that allows the Trail Rocker to power up only when the key is turned on. The system is shipped to be powered at all times. 

You'll also find a winch pigtail that is pre wired into the kit. This pigtrail is ready to wire up to your winch. The other end is ran up to the switch panel. With the purchase of our custom winch switch PN 57150. You can easily replace one of your switches and control your winch from in the cab. Be sure to visit our wiring schematics page for details on wiring this to your winch. www.painlessperformance.com/schematics

 

If you’ve never seen a Painless manual, you’re in for a treat. Scroll to the top for a PDF version of this nearly 50 page full color manual. You’ll wish we made manuals for everyday living. 

 

 

Here is the complete kit.  Everything you need to get your accessories powered safely in your TJ Jeep!

 

 

 

 

 

 Trail Rocker System Jeep Wrangler TJ 1997-06 w/Dash Mounted Panel By Painless Performance

 

 

ECM Flash Program

 

 

This is a basic start and run tune that we only recommend for a near stock application. We will only change the following parameters: delete VATS/PASS-KEY security, cooling fan on/off temperatures, rear end gear ratio, tire size, speed limiter, rpm limiter, idle rpm, and we will adjust the check engine light parameters. If your setup requires any other parameters tuned you will need to locate a local tuner. All ECMs are left unlocked to allow easy access for your tuner.

Step 1: Purchase one of the qualifying part numbers. See below for that list.


Step 2: If your part number is highlighted RED proceed to step 3B. If your part number is highlighted BLACK, proceed to step 3A.


Step 3A: If you have arrived at this step, your harness does not come with an ECM and you must provide one to be flashed. Please reference the manual with your harness to confirm the ECM part number required.


Step 4A: Once you have received your harness, please cut the Barcode label from the box as shown in the picture below.


Step 5A: Package and mail your ECM along with the Barcode label, a copy of your purchase receipt, and your ECM form that you are about to complete. (The address will be provided after you complete the form). We will pay for return ground shipping*. If you request a faster service, you will need to provide a return label.


Step 3B: If you have arrived at this step, your purchase comes with an ECM. You must fill out our ECM form BEFORE your purchase will ship. Proceed to Step 6.


Step 6: Click the “Start Here” button below to fill out our ECM questionnaire.


Step 7: Once we have the ECM, we will use the data from the form to flash the ECM. Then, once it has been flashed we will package the ECM and ship it back to you. If we encounter a question, we will contact you. This process can take 1-3 days.


Step 8: Once you receive your ECM, it is ready to go.

 

*Note: Our free return shipping is ONLY good for the lower 48 states, via ground UPS. If you are outside of those states, you must provide a return shipping label with your order. If your purchase comes with an ECM, the shipping will be covered via the retailer you purchased from.

 

 

Click the Start Here button below to get your FREE ECM Flash!

Click Here To Start The ECM Reflash Process

 

End Panel


APPLICABLE PAINLESS PART NUMBERS

60008

   

60522

60009

   

60523

60017

   

60524

60026

   

60526

60217

   

60608

60218

   

60617

60221

   

60700

60508

   

60701

60509

   

60702

60520

   

60710