Call Tech Support 1-800-423-9696

Tech Support: 1-800-423-9696
Friday 11/24/2017
Closed for the holiday

 
Trail Rocker Relay Center - Customizable By Painless Performance

P/N 57100

Trail Rocker Relay Center - Customizable

       
 

  • Application
  • Specs
  • Larger Image
American Made

 

Introducing the brand new Customizable Trail Rocker from Painless, allowing you to control up to eight accessories on your custom application! The heart of this kit is enclosed in the weatherproof housing that surrounds the power center with eight fuses and relays.  

The power center then provides you with all the necessary wiring to connect to any 12v accessory ranging from lights to air lockers. Easily installed with our detailed instructions and plug-n-play design.

Also provided is a switch input harness for controlling all of your accessories. Simply wire these connections into your own switches.   

  • Control up to 8 accessories, (8) 30 amp fuses and (8) 30 amp relays
  • Weatherproof housing around the power center
  • Allows for custom mounting
  • Allows for wiring in your own switches

Winch Ready! The Trail Rocker system includes dedicated wires for controlling a winch. Purchase of our Winch Control Add-on Kit part number 57150 is required for operation. 

 

 

 

 

The underside of the fuse & relay cover has a built in gasket to help keep any moisture out and to act as an extra support for the relays. 

Attention to detail shows in this bolt with O-ring combo to hold the top cover on.  

 

 

 

This harness attaches the fuse & relay center to your switch panel. It’s a plug-n-play design that allows for your switch panel to be disconnected if needed. 

Exiting the fuse & relay center we provide you with 21’ of wire to reach any 12 volt accessory you have.

Printed every 12” on the wire you’ll find the circuit description, a signature touch of ours. 

 

You'll also find a winch pigtail that is pre wired into the kit. This pigtrail is ready to wire up to your winch. The other end is ran up to the switch panel. With the purchase of our custom winch switch PN 57150. You can easily replace one of your switches and control your winch from in the cab. Be sure to visit our wiring schematics page for details on wiring this to your winch. www.painlessperformance.com/schematics

 

 

 

 

 

 

 Trail Rocker Relay Center - Customizable By Painless Performance

 

 

ECM Flash Program

 

 

This is a basic start and run tune that we only recommend for a near stock application. We will only change the following parameters: delete VATS/PASS-KEY security, cooling fan on/off temperatures, rear end gear ratio, tire size, speed limiter, rpm limiter, idle rpm, and we will adjust the check engine light parameters. If your setup requires any other parameters tuned you will need to locate a local tuner. All ECMs are left unlocked to allow easy access for your tuner.

Step 1: Purchase one of the qualifying part numbers. See below for that list.


Step 2: If your part number is highlighted RED proceed to step 3B. If your part number is highlighted BLACK, proceed to step 3A.


Step 3A: If you have arrived at this step, your harness does not come with an ECM and you must provide one to be flashed. Please reference the manual with your harness to confirm the ECM part number required.


Step 4A: Once you have received your harness, please cut the Barcode label from the box as shown in the picture below.


Step 5A: Package and mail your ECM along with the Barcode label, a copy of your purchase receipt, and your ECM form that you are about to complete. (The address will be provided after you complete the form). We will pay for return ground shipping*. If you request a faster service, you will need to provide a return label.


Step 3B: If you have arrived at this step, your purchase comes with an ECM. You must fill out our ECM form BEFORE your purchase will ship. Proceed to Step 6.


Step 6: Click the “Start Here” button below to fill out our ECM questionnaire.


Step 7: Once we have the ECM, we will use the data from the form to flash the ECM. Then, once it has been flashed we will package the ECM and ship it back to you. If we encounter a question, we will contact you. This process can take 1-3 days.


Step 8: Once you receive your ECM, it is ready to go.

 

*Note: Our free return shipping is ONLY good for the lower 48 states, via ground UPS. If you are outside of those states, you must provide a return shipping label with your order. If your purchase comes with an ECM, the shipping will be covered via the retailer you purchased from.

 

 

Click the Start Here button below to get your FREE ECM Flash!

Click Here To Start The ECM Reflash Process

 

End Panel


APPLICABLE PAINLESS PART NUMBERS

60008

   

60522

60009

   

60523

60017

   

60524

60026

   

60526

60217

   

60608

60218

   

60617

60221

   

60700

60508

   

60701

60509

   

60702

60520

   

60710