Contact Us
Find a Dealer
Order a Free Catalog
Tech Support And Warranty

Current and Past Rebates
Call Tech Support 1-800-423-9696

Tech Support: 1-800-423-9696
Saturday 09/23/2017
Closed on Saturday

New Products

 

Looking for the latest developments at Painless Performance?

We're proud that we’ve been your single source for automotive electrical needs for 27 years. We're constantly growing with new products that meet your expectations of quality and affordability. Take a moment and browse some of the new products that we’ve recently added to our catalog.

2007-2016 Jeep Wrangler JK Trail Rocker Accessory Control System (w/o Switches)
Part #57005


Painless Performance Part # 57005

Wire up your own switches with the Trail Rocker Relay Center from Painless, allowing you to control up to eight accessories on your JK Jeep! This kit uses the same relay center found in our other Trail Rocker systems. However, it comes without the switch panel allowing you to wire up your own switches.

The heart of this kit is enclosed in the weatherproof housing that surrounds the relay center with eight fuses and relays. This kit provides you with all the necessary weatherproof connectors and wiring to connect to your Jeep accessories ranging from lights to air lockers. Easily installed with our detailed instructions and plug-n-play design.

  • Control up to 8 accessories, (8) 30 amp fuses and (8) 30 amp relays
  • Weatherproof housing around the power center and connections
  • Custom bolt-on powder coated bracket for the power center
  • Includes all the of the required wiring

Winch Ready! The Trail Rocker system includes dedicated wires for controlling a winch. Purchase of our Winch Control Add-on Kit part number 57150 is required for operation. 

*Works with manual and automatic transmissions

 

The heart of the Trail Rocker is the fuse & relay center. Here you will find eight 30 amp fuses and eight 30 amp relays. 

The top of the weatherproof fuse & relay center features the stylish logo silkscreened onto it. Along with the fused power source mounted next to it.  

The 200 Amp MIDI fuse comes pre-installed and prewired. There’s no worrying about how to crimp that 6 gauge power cable. 

The underside of the fuse & relay cover has a built in gasket to help keep any moisture out and to act as an extra support for the relays. This extra support on the relays ensures that no matter how good or bad you are on the trails, the relays will not pop out of place. 

Attention to detail shows in this bolt with O-ring combo to hold the top cover on.  

Underneath the fuse & relay center you will find the powder coated custom mounting bracket with stainless hardware. This bracket is designed to install in existing mounting holes under the hood. 

This harness attaches the fuse & relay center to the switchs of your choice.   

Exiting the fuse & relay center we provide you with 21’ of wire to reach any 12 volt accessory you have.

Printed every 12” on the wire you’ll find the circuit description, a signature touch of ours. 

The parts kit comes with everything you’ll need to install the Trail Rocker, except the tools and the Jeep.

You’ll also find a custom pigtail that allows the Trail Rocker to power up only when the key is turned on. The system is shipped to be powered at all times. 

If you’ve never seen a Painless manual, you’re in for a treat. Scroll to the top for a PDF version of this nearly 50 page full color manual. You’ll wish we made manuals for everyday living. 

 

Here is the complete kit.  Everything you need to get your accessories powered safely in your JK Jeep!

 

 


   

2011-2016 Jeep Wrangler JK Trail Rocker Accessory Control System (Tan Dash)
Part #57001


Painless Performance Part # 57001

Introducing the brand new Trail Rocker from Painless, allowing you to control up to eight accessories on your JK Jeep! The heart of this kit is enclosed in the weatherproof housing that surrounds the power center with eight fuses and relays. Controlling it, are five prewired switches mounted in our custom dash panel for a clean factory installed look inside your Jeep.

The power center then provides you with all the necessary weatherproof connectors and wiring to connect to your Jeep
accessories ranging from lights to air lockers. Easily installed with our detailed instructions and plug-n-play design.

Provided are 5 switches pre-wired to control 6 accessories with ease!  Also included are two extra Output Wires that are easily wired into one of the 5 existing switches giving you control of up to 8 total accessories.  

•Control up to 8 accessories, (8) 30 amp fuses and (8) 30 amp relays
•Weatherproof housing around the power center and connections
•Custom bolt-on powder coated bracket for the power center
•Switch panel mounts 5 LED switches in a factory non-intrusive dash location

Winch Ready! The Trail Rocker system includes dedicated wires for controlling a winch. Purchase of our Winch Control Add-on Kit part number 57150 is required for operation. 

(Automatic Transmission Applications Only)

The moment you know you’re in good hands. The Painless Trail Rocker comes shipped and packaged to ensure the product arrives to you undamaged. 

The heart of the Trail Rocker is the fuse & relay center. Here you will find eight 30 amp fuses and eight 30 amp relays. While the switch panel only comes with six total switches, we provide you with the two extra circuits for doubling up on dual high amp systems. Say for example, two 20 amp lights powered off of two relays but only one switch. 

The top of the weatherproof fuse & relay center features the stylish logo silkscreened onto it. Along with the fused power source mounted next to it.  

The 200 Amp MIDI fuse comes pre-installed and prewired. There’s no worrying about how to crimp that 6 gauge power cable. 

The underside of the fuse & relay cover has a built in gasket to help keep any moisture out and to act as an extra support for the relays. This extra support on the relays ensures that no matter how good or bad you are on the trails, the relays will not pop out of place. 

Attention to detail shows in this bolt with O-ring combo to hold the top cover on.  

Underneath the fuse & relay center you will find the powder coated custom mounting bracket with stainless hardware. This bracket is designed to install in existing mounting holes under the hood. 

These switches are vibration, shock, thermoshock, moisture, and salt spray resistant. What more could you want? Custom etched switches….coming soon! 

The back side of the switch panel comes pre terminated and ready to plug into the fuse & relay center. We also pre-route the two extra output wires to the panel. This allows you to either piggy back extra components off of a switch or to replace the on/off switches with more on/off/on ones. 

This harness attaches the fuse & relay center to the switch panel. It’s a plug-n-play design that only requires you to route it and plug it in.  

Exiting the fuse & relay center we provide you with 21’ of wire to reach any 12 volt accessory you have.

Printed every 12” on the wire you’ll find the circuit description, a signature touch of ours. 

The parts kit comes with everything you’ll need to install the Trail Rocker, except the tools and the Jeep.

You’ll also find a custom pigtail that allows the Trail Rocker to power up only when the key is turned on. The system is shipped to be powered at all times. 

If you’ve never seen a Painless manual, you’re in for a treat. Scroll to the top for a PDF version of this nearly 50 page full color manual. You’ll wish we made manuals for everyday living. 

Here is the complete kit.  Everything you need to get your accessories powered safely in your JK Jeep!

The switch panel mounts directly in front of your shifter giving you a clean, factory-installed look.

 


   

2011-2016 Jeep Wrangler JK Trail Rocker Accessory Control System (Black Dash)
Part #57000


Painless Performance Part # 57000

Introducing the brand new Trail Rocker from Painless, allowing you to control up to eight accessories on your JK Jeep! The heart of this kit is enclosed in the weatherproof housing that surrounds the power center with eight fuses and relays. Controlling it, are five prewired switches mounted in our custom dash panel for a clean factory installed look inside your Jeep.

The power center then provides you with all the necessary weatherproof connectors and wiring to connect to your Jeep
accessories ranging from lights to air lockers. Easily installed with our detailed instructions and plug-n-play design.

Provided are 5 switches pre-wired to control 6 accessories with ease!  Also included are two extra Output Wires that are easily wired into one of the 5 existing switches giving you control of up to 8 total accessories.  

•Control up to 8 accessories, (8) 30 amp fuses and (8) 30 amp relays
•Weatherproof housing around the power center and connections
•Custom bolt-on powder coated bracket for the power center
•Switch panel mounts 5 LED switches in a factory non-intrusive dash location

Winch Ready! The Trail Rocker system includes dedicated wires for controlling a winch. Purchase of our Winch Control Add-on Kit part number 57150 is required for operation. 

(Automatic Transmission Applications Only)

The moment you know you’re in good hands. The Painless Trail Rocker comes shipped and packaged to ensure the product arrives to you undamaged. 

The heart of the Trail Rocker is the fuse & relay center. Here you will find eight 30 amp fuses and eight 30 amp relays. While the switch panel only comes with six total switches, we provide you with the two extra circuits for doubling up on dual high amp systems. Say for example, two 20 amp lights powered off of two relays but only one switch. 

The top of the weatherproof fuse & relay center features the stylish logo silkscreened onto it. Along with the fused power source mounted next to it.  

The 200 Amp MIDI fuse comes pre-installed and prewired. There’s no worrying about how to crimp that 6 gauge power cable. 

The underside of the fuse & relay cover has a built in gasket to help keep any moisture out and to act as an extra support for the relays. This extra support on the relays ensures that no matter how good or bad you are on the trails, the relays will not pop out of place. 

Attention to detail shows in this bolt with O-ring combo to hold the top cover on.  

Underneath the fuse & relay center you will find the powder coated custom mounting bracket with stainless hardware. This bracket is designed to install in existing mounting holes under the hood. 

These switches are vibration, shock, thermoshock, moisture, and salt spray resistant. What more could you want? Custom etched switches….coming soon! 

The back side of the switch panel comes pre terminated and ready to plug into the fuse & relay center. We also pre-route the two extra output wires to the panel. This allows you to either piggy back extra components off of a switch or to replace the on/off switches with more on/off/on ones. 

This harness attaches the fuse & relay center to the switch panel. It’s a plug-n-play design that only requires you to route it and plug it in.  

Exiting the fuse & relay center we provide you with 21’ of wire to reach any 12 volt accessory you have.

Printed every 12” on the wire you’ll find the circuit description, a signature touch of ours. 

The parts kit comes with everything you’ll need to install the Trail Rocker, except the tools and the Jeep.

You’ll also find a custom pigtail that allows the Trail Rocker to power up only when the key is turned on. The system is shipped to be powered at all times. 

If you’ve never seen a Painless manual, you’re in for a treat. Scroll to the top for a PDF version of this nearly 50 page full color manual. You’ll wish we made manuals for everyday living. 

 

 

Here is the complete kit.  Everything you need to get your accessories powered safely in your JK Jeep!

The switch panel mounts directly in front of your shifter giving you a clean, factory-installed look.

 

 


   

26 Circuit Direct Fit 1969 Camaro Harness
Part #20202


Painless Performance Part # 20202

Your most complete '69 Camaro Harness! Featuring 26 circuits with virtually every connector installed on the harness out of the box. This harness covers all common options and even features a fully integrated ground circuit.  Included are provisions for the RS headlights and taillights, cowl hood, and even a complete console harness!  Also available is our 120+ page manual full of color schematics, photos, and step-by-step instructions!                                          

 

  • Numerous components have the connectors and terminals pre-installed to make connections plug-n-play
  • All exterior lights have the correct sockets and bulbs pre-installed
  • 6 gauge charge wire and 150 amp MIDI fuse
  • Fully integrated ground circuit
  • 120+ page manual full of color schematics, photos, and step-by-step instructions

Here are some of the great features included with this kit. 

The heart of your new Camaro wiring harness is centered around this factory style precision molded fuse block.  Updated ATC style fuses ensure that the 26 circuits stay protected and safe.

The backside of the fuse block utilizes a factory style bulkhead connector to ensure there is no trimming or cutting to your firewall.  This allows you to easily install the fuse block in the factory location.

Plug and play design makes install easy, no matter your options.  Also included are pre-terminated connectors for either standard or RS taillight options.  Don't have RS taillights now but may add them down the road?  Simply unplug the new connector and plug in the new one!

The new status indicator circuit boards replace the brittle factory indicator light molded plastic and provide color correct incondescent bulbs to retain the factory look.  Ever need to replace a bulb down the road?  The board are easily unplugged and removed and bulb changes are a breeze!

Each pre-terminated connector is tagged for easy routing and installation. 

There is no need to make extra trips to the parts store with this kit.  Connectors, terminals, extra fuses, light bulbs, etc., all come in the box.  Any questions while installing?  Just refer to the complete 120+ page installation manual, or give our tech line a call!

 


   

Ford 3G Alternator Harness
Part #30831


Painless Performance Part # 30831

The popular Ford 3G Alternator conversion just got easier. The Painless 3G kit takes the parts chase away from this ever growing charging system upgrade. Until now, pigtails, large gauge charge wire, and a heavy duty inline fuse have all had to be sourced individually. This kit comes with both alternator connectors pre-installed, 8’ of large 6 gauge charge wire, a weather-proof fuse holder with a heavy duty 150 amp inline fuse, detailed instructions, and all weatherproof splices & ring terminals needed for a proper install.


   

28 Circuit Fuse Block Cover
Part #12001


Painless Performance Part # 12001

 

Designed to snap onto our 28 circuit fuse block. This cover helps keep dirt, dust, and moisture from comming into direct contact with the fuse block. It also helps clean up the apprearance in areas that the fuse block may be visable.

 

Will not fit 30003 fuse block


   

1999 - 2006 GM Gen III 4.8, 5.3 & 6.0L Harness Std. Length Mechanical TB
Part #60217


Painless Performance Part # 60217

This harness is designed for the 1999-2006 4.8L, 5.3L, 6.0L mechanical throttle body engines using an LS1 / LS6 PCM with a 4L65E, 4L70E, 4L80E, 4L85E, or manual transmission. 2003-2006 Engines will require a mechanical throttle body to be installed. 2003-2006 engines which were originally flex fuel will also require Delphi Multec 2 (factory truck style) injectors to be installed. Harnesses do not include connections for the rear O2 sensors or fuel tank pressure sensor but are available separate. Included with this harness is a 10 circuit weatherproof fuse block and GM color coded wires with labels for easy installation. 

This standard length harness allows four feet from the back of the intake manifold to where the fuseblock and ECM mount.  Perfect for those that plan to mount these components under the dash or in the glove box.

This kit includes:

  1. All new fuel injection harness with OEM fitment connectors and harness breakouts
  2. OBDII connector, mounting bracket and check engine light
  3. Rubber grommet
  4. Mounting hardware

Purchase this harness today and qualify for Painless Performance®™ to flash your ECM for free.  Click here for details.

**Please note that this harness does not support Flex Fuel USCAR Injectors.** 

We recommend checking the online manual for the full list of required mating parts prior to ordering.  


   

17 Circuit Customizable Nostalgia All Black Chassis Harness
Part #10309


Painless Performance Part # 10309

This 17 circuit harness with all black wire insulation can help your vehicle look clean and help blend your harness into the background of your vehicle. Are you looking for a very simple to install harness with the flexibility of the fuseblock to be installable anywhere on your vehicle? This harness' unique construction has two major sections: Power Supply Harness w/preterminated Fuse Block and the Output Supply Harness. This design allows for the fuse block to virtually be installed anyway on your vehicle. This can be especially useful when building an earlier vehicle without a lot of room under it's dashboard. You'll also find many upgrades in this harness such as a 6 gauge charge wire and a 150 amp midi fuse. Also available is a 100+ page color step-by-step instruction manual with many useful schematics for adding some of the most common aftermarket upgraded parts to your vehicle. 


   

PERFECT TORC GM 4L60/65E & 4L80/85E Transmission Controller
Part #66501


Painless Performance Part # 66501

State-of-the-Art stand-alone transmission controller for the General Motors 4-speed 4L60/65E and 4L80/85E automatics. Fully compatible with carburated, fuel injected and diesel engines. Laptop software included with several "base" calibrations to start off with for each application.

If you are using a GM 4L60E, it will fit 1996 and newer GM 4L60E transmissions only. (On later model 4L65E models it is not necessary to plug into the input shaft speed sensor.)

If you are using a GM 4L80E, it will fit 1995 and newer GM 4L80E transmissions only. (If earlier unit is desired to be used; the "Bosch" style pressure control solenoid MUST be replaced with the newer "Holley" style pressure control solenoid.

Be sure to click on the "Manual" link and download a copy of the TORC instructions to read about why it is the simplest electronic transmission controller on the market.


   

GM Gen IV Tachometer Driver
Part #60150


Painless Performance Part # 60150

This small device converts the 5 Volt 58X crank sensor signal from any Gen IV GM V8 engine into a 12 Volt signal usuable by most aftermarket and OEM tachometers.

Four wire connections to your vehicle and a simple calibration to run through will get your new tachometer up and running.


   

26 Circuit Direct Fit 1974-77 Camaro Harness
Part #20113


Painless Performance Part # 20113

This 26 circuit direct fit 1974-1977 2nd Gen Camaro harnesses has virtually every connector installed on the harness out of the box. This harnesses are split into three sections (engine, interior, & rear) and features a fully integrated ground circuit. You'll find many upgrades in ths harnesses such as a 6 gauge charge wire and a 150 amp midi fuse. Also available is a 150+ page full color step by step manual that also covers many alternative wiring options and each wire is custom printed with the circuit identification as well as using GM color codes for easy installation. 

NOTE: Factory A/C wiring is not included, as this option seemed to almost change year to year. These harnesses DO include the power wire for the A/C switch to make it as easy as plugging in your original A/C harness, an aftermarket reproduction harness, or an aftermarket A/C system. These harnesses DO include a new blower motor harness for those with heat only systems. 

Wiring for factory power window/locks is also not included but available as a separate part number. Painless part # 30715 is a factory style power window/power lock harness for these vehicles if a replacement harness for this option is needed. Like the A/C wires, these chassis harnesses DO include the power wires for the power window/lock option making it another easy plug in to a factory power window/lock harness or the Painless Power Window/Lock Harness.

 


   

26 Circuit Direct Fit 1978-81 Camaro Harness
Part #20114


Painless Performance Part # 20114

This 26 circuit direct fit 1978-1981 2nd Gen Camaro harnesses has virtually every connector installed on the harness out of the box. This harnesses are split into three sections (engine, interior, & rear) and features a fully integrated ground circuit. You'll find many upgrades in ths harnesses such as a 6 gauge charge wire and a 150 amp midi fuse. Also available is a 150+ page full color step by step manual that also covers many alternative wiring options and each wire is custom printed with the circuit identification as well as using GM color codes for easy installation. 

NOTE: Factory A/C wiring is not included, as this option seemed to almost change year to year. These harnesses DO include the power wire for the A/C switch to make it as easy as plugging in your original A/C harness, an aftermarket reproduction harness, or an aftermarket A/C system. These harnesses DO include a new blower motor harness for those with heat only systems. 

Wiring for factory power window/locks is also not included but available as a separate part number. Painless part # 30715 is a factory style power window/power lock harness for these vehicles if a replacement harness for this option is needed. Like the A/C wires, these chassis harnesses DO include the power wires for the power window/lock option making it another easy plug in to a factory power window/lock harness or the Painless Power Window/Lock Harness.

 


   

Painless Gauge Controller
Part #60650


Painless Performance Part # 60650

Notice: This product is not currently compatible with GMPP engine harness kits. We are currently working on updating the Gauge Controller to work with this kit. May/2015

 

Are you running a modern LSx drivetrain in an older vehicle? If so, you have probably contemplated how you are going to run all of your aftermarket gauges. Up until now your only option was to purchase all the sensors you needed individually and install them to run just the gauges, even though your modern LSx drivetrain already has the necessary sensors integrated into its computer control systems. If running redundant sensors seems a bit...well… redundant, then the LS Gauge Controller is just the product you need. This module uses the information that is already available through your OBDII port, eliminating the need to run duplicate sensors for your various gauge functions. This information is communicated through a system called the “Controller Area Network”, or CAN for short. Once the Gauge Controller Module has been connected to the CAN system you will have the ability to run most aftermarket speedometer, tachometer, coolant temperature, oil pressure*, and fuel level* gauges. The Gauge Controller Module takes the raw data from the CAN system then converts it to a simple user programmable signal for your aftermarket gauges. The module is compatible with all gas engine drivetrains from General Motors that are 1996 and newer. All of those will support speedometer, tachometer, and coolant temperature. Select applications will also support oil pressure and fuel level. See the specs page for more information. 

*Not available for all applications. 

 


   

28 Circuit Direct Fit 1966-77 Bronco Harness w/o switches
Part #10114


Painless Performance Part # 10114

Designed with input from Bronco owners everywhere, this 28 circuit direct fit 1966-1977 Bronco harness sets a new standard in wiring. This harness includes a molded plastic glove box that not only replaces the factory cardboard one, it also mounts our weatherproof fuse block. You'll also find factory-style molded exterior light connectors, Ford turn signal connectors and a Ford dimmer switch connector. This harness has most of the factory connections are already pre-terminated. Also available is an 80+ page full color step by step install manual with over 80 photos, drawings and harness schematics. Each wire is custom printed with the circuit identification as well as using Ford color codes for easy installation.  

 

Here are some of the great features included with this kit. 

 

The heart of your new Bronco wiring harness is centered around this weatherproof fuse block.  With 28 total circuits and 9 accessories circuits, this harness will support most features and add-ons you want to add to your Bronco.  

 

Underneath the fuse block we can see the weatherproof terminals and covered power supply post. 

 

Included with your Bronco harness is a custom molded glovebox. This is also the mounting location for your fuse block. 

 

Properly mounting and routing your wiring harness is a critical step to avoid any premature wear to your wiring. We provide you with enough zip ties and grommets to make sure you avoid any issues.

 

Included in your parts kit you’ll find terminals, weatherproof splices, screws, extra fuses etc.

 

One of the many features of your new Bronco harness allows you to add an aftermarket tach. 

 

No matter if you have an early, mid, or later model column, we’ve provided you with a pigtail to adapt them all to your new Bronco harness. 

 

All of your rear lights are properly insulated making for a plug-n-play install.

 

As with every wiring kit from Painless, you’ll find our signature printed wire. They tell you the wire number, where it’s coming from, and where it’s going to. 

 


   

2007-2010 Jeep Wrangler JK Trail Rocker Accessory Control System
Part #57002


Painless Performance Part # 57002

Introducing the brand new Trail Rocker from Painless, allowing you to control up to eight accessories on your JK Jeep! The heart of this kit is enclosed in the weatherproof housing that surrounds the power center with eight fuses and relays. Controlling it, are five prewired switches mounted in our custom dash panel for a clean factory installed look inside your Jeep.

The power center then provides you with all the necessary weatherproof connectors and wiring to connect to your Jeep
accessories ranging from lights to air lockers. Easily installed with our detailed instructions and plug-n-play design.

Provided are 4 switches pre-wired to control 6 accessories with ease!  Also included are two extra Output Wires that are easily wired into one of the 4 existing switches giving you control of up to 8 total accessories.  

•Control up to 8 accessories, (8) 30 amp fuses and (8) 30 amp relays
•Weatherproof housing around the power center and connections
•Custom bolt-on powder coated bracket for the power center
•Switch panel mounts 4 LED switches in a factory non-intrusive dash location

Winch Ready! The Trail Rocker system includes dedicated wires for controlling a winch. Purchase of our Winch Control Add-on Kit part number 57150 is required for operation. 

Works with Auto and Manual Transmission applications. 

The moment you know you’re in good hands. The Painless Trail Rocker comes shipped and packaged to ensure the product arrives to you undamaged. 

The heart of the Trail Rocker is the fuse & relay center. Here you will find eight 30 amp fuses and eight 30 amp relays. While the switch panel only comes with six total switches, we provide you with the two extra circuits for doubling up on dual high amp systems. Say for example, two 20 amp lights powered off of two relays but only one switch. 

The top of the weatherproof fuse & relay center features the stylish logo silkscreened onto it. Along with the fused power source mounted next to it.  

The 200 Amp MIDI fuse comes pre-installed and prewired. There’s no worrying about how to crimp that 6 gauge power cable. 

The underside of the fuse & relay cover has a built in gasket to help keep any moisture out and to act as an extra support for the relays. This extra support on the relays ensures that no matter how good or bad you are on the trails, the relays will not pop out of place. 

Attention to detail shows in this bolt with O-ring combo to hold the top cover on.  

Underneath the fuse & relay center you will find the powder coated custom mounting bracket with stainless hardware. This bracket is designed to install in existing mounting holes under the hood. 

These switches are vibration, shock, thermoshock, moisture, and salt spray resistant. What more could you want? Custom etched switches….coming soon! 

The back side of the switch panel comes pre terminated and ready to plug into the fuse & relay center. We also pre-route the two extra output wires to the panel. This allows you to either piggy back extra components off of a switch or to replace the on/off switches with more on/off/on ones. 

This harness attaches the fuse & relay center to the switch panel. It’s a plug-n-play design that only requires you to route it and plug it in.  

Exiting the fuse & relay center we provide you with 21’ of wire to reach any 12 volt accessory you have.

Printed every 12” on the wire you’ll find the circuit description, a signature touch of ours. 

The parts kit comes with everything you’ll need to install the Trail Rocker, except the tools and the Jeep.

You’ll also find a custom pigtail that allows the Trail Rocker to power up only when the key is turned on. The system is shipped to be powered at all times. 

If you’ve never seen a Painless manual, you’re in for a treat. Scroll to the top for a PDF version of this nearly 50 page full color manual. You’ll wish we made manuals for everyday living. 

Here is the complete kit.  Everything you need to get your accessories powered safely in your JK Jeep!

 

 


   

26 Circuit Direct Fit 1968 Chevelle / Malibu Harness
Part #20128


Painless Performance Part # 20128

This harness gives you everything you need, plus more! Not only are there provisions for connecting standard factory components, we also provide what you will need for aftermarket components. Including options like a console sub-harness, two gauge cluster pigtails, and even a fully integrated ground circuit. This harness follows all of the same routing found on the factory harness which allows you to utilize the factory harness attachment points. Extra length has even been added to the headlight section to be routed behind the driver side inner fender for a cleaner look. Also available is a 120+ page manual full of color schematics, photos, and step-by-step instructions!

 

  • Numerous components have the connectors and terminals pre-installed to make connections plug-n-play
  • All exterior lights have the correct sockets and bulbs pre-installed
  • 6 gauge charge wire and 150 amp MIDI fuse
  • Fully integrated ground circuit
  • 120+ page manual full of color schematics, photos, and step-by-step instructions

Note: Options not supported in these harnesses are:  wiring for the TCS relay for turbo 400 transmissions, wiring for the factory power window/locks, and factory A/C wiring. These harnesses do include the switch power wire for the factory power window/locks and A/C. These harnesses do include a new blower motor harness for those with heat only systems. 

Here are some of the great features included with this kit. 

The heart of your new Chevelle wiring harness is centered around this factory style precision molded fuse block.  Updated ATC style fuses ensure that the 26 circuits stay protected and safe.

The backside of the fuse block utilizes a factory style bulkhead connector to ensure there is no trimming or cutting to your firewall.  This allows you to easily install the fuse block in the factory location.

Plug and play design makes install easy, no matter your options.  Don't have a center console but may add one later?  The included console harness can be easily added at any time.

Each pre-terminated connector is tagged for easy routing and installation. 

There is no need to make extra trips to the parts store with this kit.  Connectors, terminals, extra fuses, light bulbs, etc., all come in the box.  Any questions while installing?  Just refer to the complete 120+ page installation manual, or give our tech line a call!

 


   

26 Circuit Direct Fit 1969 Chevelle / Malibu Harness
Part #20129


Painless Performance Part # 20129

This harness gives you everything you need, plus more! Not only are there provisions for connecting standard factory components, we also provide what you will need for aftermarket components. Including options like a console sub-harness, two gauge cluster pigtails, and even a fully integrated ground circuit. This harness follows all of the same routing found on the factory harness which allows you to utilize the factory harness attachment points. Extra length has even been added to the headlight section to be routed behind the driver side inner fender for a cleaner look. Also available is a 120+ page manual full of color schematics, photos, and step-by-step instructions!

 

  • Numerous components have the connectors and terminals pre-installed to make connections plug-n-play
  • All exterior lights have the correct sockets and bulbs pre-installed
  • 6 gauge charge wire and 150 amp MIDI fuse
  • Fully integrated ground circuit
  • 120+ page manual full of color schematics, photos, and step-by-step instructions

 

Note: Options not supported in these harnesses are:  wiring for the TCS relay for turbo 400 transmissions, wiring for the factory power window/locks, and factory A/C wiring. These harnesses do include the switch power wire for the factory power window/locks and A/C. These harnesses do include a new blower motor harness for those with heat only systems. 

Here are some of the great features included with this kit. 

The heart of your new Chevelle wiring harness is centered around this factory style precision molded fuse block.  Updated ATC style fuses ensure that the 26 circuits stay protected and safe.

The backside of the fuse block utilizes a factory style bulkhead connector to ensure there is no trimming or cutting to your firewall.  This allows you to easily install the fuse block in the factory location.

Plug and play design makes install easy, no matter your options.  Don't have a center console but may add one later?  The included console harness can be easily added at any time.

Each pre-terminated connector is tagged for easy routing and installation. 

There is no need to make extra trips to the parts store with this kit.  Connectors, terminals, extra fuses, light bulbs, etc., all come in the box.  Any questions while installing?  Just refer to the complete 120+ page installation manual, or give our tech line a call!