Open today at 8AM CDT

Contact
Support 1.800.423.9696

Trail Rocker Relay Center 2007-2018 Jeep JK (Wrangler) (w/o Switches) 57005


 

Suggested Parts
The recommended parts below work well with Part number 57005

57000

View Product

Also Buy
Trail Rocker Jeep JK 11-18 Black Dash Panel

57001

View Product

Also Buy
Trail Rocker Jeep JK 11-18 Tan Dash Panel

57002

View Product

Also Buy
Trail Rocker Jeep JK 07-10 Black Dash Panel

57003

View Product

Also Buy
Trail Rocker Jeep JK 11-18 Overhead 6 Swt

57004

View Product

Also Buy
Trail Rocker Jeep JK 11-18 Overhead 6 Swt w/Drop down


        $349.99

WarningProp 65 Warning
Hazardous Material Warning

Warning
WARNING: This product can expose you to chemicals including lead which is known to the State of California to cause cancer or birth defects or other reproductive harm. For more information, visit www.P65warnings.ca.gov.


  • Application
  • Specs
Part Number: 57005
Year: 2007-2018
Make: Jeep
Model: Wrangler
Engine: 3.6-liter Pentastar V6
Trans.: Automatics(922.6/NAG1) and Manual Transmissions(NSG370)

 

THIS Trail Rocker Relay Center from Painless, allows you to control up to eight accessories on your Jeep JK! It uses the same relay center found in our other Trail Rocker systems, yet it includes a custom made bracket to easily mount this Relay Center conveinently under the hood; next to the factory battery location.

 

THIS kit is designed for those who want to mount their own control switches into the plastic panels on their Jeep's dash. This kit is designed to allow you to install and wire up your own switches.

The heart of this kit is a weatherproof housing that surrounds the relays and fuses protecting them from the elements. Included in this kit are all the necessary weatherproof heat shrink and splices to connect your Jeep accessories ranging from lights, air pumps, E-Lockers, Winch Control and even refridgerators. Our detailed step-by-step instructions clearly support this kits plug-n-play design.

  • Controls up to 8 accessories with (8) 30 amp fuses and (8) 30 amp relays
  • Weatherproof housing to protect Fuse and Relays from the elements
  • Custom bolt-on Jeep JK Specific, powder coated bracket for the Relay Center
  • Includes 21ft long, 12 gauge output wires to allow maximum current delivery to your accessories. It's no problem to power up an accessory on the opposite end of your Jeep!
  • Includes 7 ft long, 18 gauge switch control wires, so simply pass them through the firewall and connect your switches. 

Winch Ready! The Trail Rocker Relay Center includes dedicated wires for controlling a winch. Purchase one of the Trail Rocker Winch Control Add-on Kits, part number 57150 to easily add winch control to your Jeep JK. 

*This kit works with manual and automatic transmissions.

 

The heart of the Trail Rocker is the fuse & relay center. Here you will find eight 30 amp fuses and eight 30 amp relays. 

The top of the weatherproof fuse & relay center features the stylish logo silkscreened onto it. Along with the fused power source mounted next to it.  

The 200 Amp MIDI fuse comes pre-installed and prewired. There’s no worrying about how to crimp that 6 gauge power cable. 

The underside of the fuse & relay cover has a built in gasket to help keep any moisture out and to act as an extra support for the relays. This extra support on the relays ensures that no matter how good or bad you are on the trails, the relays will not pop out of place. 

Attention to detail shows in this bolt with O-ring combo to hold the top cover on.  

Underneath the fuse & relay center you will find the powder coated custom mounting bracket with stainless hardware. This bracket is designed to install in existing mounting holes under the hood. 

This harness attaches the fuse & relay center to the switchs of your choice.   

Exiting the fuse & relay center we provide you with 21’ of wire to reach any 12 volt accessory you have.

Printed every 12” on the wire you’ll find the circuit description, a signature touch of ours. 

The parts kit comes with everything you’ll need to install the Trail Rocker, except the tools and the Jeep.

You’ll also find a custom pigtail that allows the Trail Rocker to power up only when the key is turned on. The system is shipped to be powered at all times. 

 

You'll also find a winch pigtail that is pre wired into the kit. This pigtrail is ready to wire up to your winch. The other end is ran up to the switch panel. With the purchase of our custom winch switch PN 57150. You can easily replace one of your switches and control your winch from in the cab. Be sure to visit our wiring schematics page for details on wiring this to your winch. www.painlessperformance.com/schematics

If you’ve never seen a Painless manual, you’re in for a treat. Scroll to the top for a PDF version of this nearly 50 page full color manual. You’ll wish we made manuals for everyday living. 

 

Here is the complete kit.  Everything you need to get your accessories powered safely in your JK Jeep!

 

 

Number of Circuits: (8) 30 AMP Outputs, (8) Relay Control B+ Inputs, (2) Winch Control Wires
Harness Length: 21 ft. long 12 gauge wires included
Fuse Type: Standard Automotive Blade Fuses with LED Indicator for open fuse indication
Firewall Passthrough: Grommet Provided In Kit
Color Code Based:  Painless Specific
Connections Included: All high current fuse and feed circuits to each outputs individual fuse and relay are terminated with exacting tolerances for peak product performance and life.

 

Suggested Parts

 

57000

View

Also Buy
Trail Rocker Jeep JK 11-18 Black Dash Panel

 

57001

View

Also Buy
Trail Rocker Jeep JK 11-18 Tan Dash Panel

 

57002

View

Also Buy
Trail Rocker Jeep JK 07-10 Black Dash Panel

 

57003

View

Also Buy
Trail Rocker Jeep JK 11-18 Overhead 6 Swt

 

57004

View

Also Buy
Trail Rocker Jeep JK 11-18 Overhead 6 Swt w/Drop down

 

57150

View

Also Buy
Trail Rocker Winch Control Add-On Kit